AET - AUTOMATIC ALIGNER ESCALATOR
Automatic notch finder/escalator aligns and escalates wafers for ID mark reading.
Unit features operator selected tilt angle for enhanced ID readability.
Optional LED light bank furnishes optimal lighting conditions for ID reading.
H-Square's patented notch finding mechanisms result in exceptional aligning accuracy.
User-friendly control panel facilitates ease of use.
Cost-effective design and operator visual reading provides wafer tracking at a fraction of
the cost of fully automated OCR systems.
ESD safe construction. Class 1 cleanroom compatible.
100mm FLAT AETWFA4 125mm FLAT AETWFA5
150mm FLAT AETWFA6 150mm NOTCH AETWNA6
200mm FLAT AETWFA8 200mm NOTCH AETWNA8
|
|
ETAS1 - MANUAL WAFER ESCALATOR
Manual escalator lifts wafers incrementally when cassette is placed on unit.
Wafers are tilted 25º to enhance ID readability.
Plastic ESD safe construction makes unit idea for all applications.
Models with varying tilt angles can be ordered through the Custom Products Department
100mm ETAS1-4
125mm ETAS1-5
150mm ETAS1-6
200mm ETAS1-8
|
|
WB5L1 - FIVE WAFER LIFTER PRESENTER
Five wafer lifter elevates five wafers simultaneously to allow easy and safe access for
wafer wands or inspection. Precise mechanical lift and selection mechanism provides
clean, smooth operation and durability. Unit eliminates the need to place vacuum tips
between consecutive wafers, which can cause scratching. Compact design saves
cleanroom space. Accommodates most high and low profile cassettes. Ergonomic and
Safety Department approved.
100mm,125mm, or 150mm WB5L1-456
200mm WB5L1-8
|
|
WP - AUTOMATIC WAFER PRESENTER
Programmable semiautomatic presentation station lifts wafers out of cassettes.
Applications include removing/replacing wafers to/from a cassette or 100% visual
inspection or identification of individual wafers.
Special v-groove saddle gently lifts wafers without contacting others in the cassette.
Units can be used with vacuum wands or outside diameter mechanical edge picks.
Class 1 cleanroom compatible.
50mm WP2
75mm WP3
100mm WP4
125mm WP5
150mm WP6
200mm WP18
|
|
WPR - AUTOMATIC WAFER PRESENTER WITH ROTATION
Programmable semiautomatic presentation station with wafer rotation.
Lifts wafers out of cassettes. Applications include removing/replacing wafers to/from a
cassette or 100% visual inspection or identification of individual wafers. Orientation of the
wafer can be "flipped" 180 degrees for special backside or front:front back: back
applications. Special v-groove saddle gently lifts wafers without contacting others in the
cassette. Units can be used with vacuum wands or outside diameter mechanical edge
picks. Unique flange design allows for WPR to drop into a hole cut into a cleanroom table.
Class 1 cleanroom compatible.
50mm WPR2 75mm WPR3
100mm WPR4 125mm WPR5
150mm WPR6 200mm WPR8
|
|
HL - MANUAL WAFER PRESENTER
A manual wafer presenter station for removing/replacing wafers to/from a cassette or for
100% inspection or identification of individual wafers. Special v-groove saddle gently lifts
wafers without contacting others in the cassette. Tool can be used with vacuum wands or
outside diameter mechanical edge picks. Class 10 cleanroom compatible.
50mm HL-2
75mm HL-3
100mm HL-4
150mm HL-6
200mm HL-8
|
|
MISC2100 SERIES - MANUAL LIFTER BLOCK
H-Square manufacturers wafer lifter blocks where the wafers are lifted from a process
cassette either above the top plane of the cassette or only partially lifted at some sub
level. H-Square has designs for lifting all wafers or only specific wafers being removed
from the cassette. Please contact H-Square Custom Products Department or your local
representative for more information.
|
|
FS-002 - FOUP STAND
Stand alone stainless-steel floor-mounted manual FOUP stand provides ergonomic safe
means to gain access to wafers off-line. Operator-friendly design aligns FOUP, FOSB, or
open bottom 300mm cassette, with the operator’s body and line-of-sight. The 360 degree
rotation with positive stop points allows any operator to find a comfortable position for
safely handling 300mm wafers to/from the specified carrier. The FS-002 features a
telescoping stand for ergonomically adjusting the height of the FOUP for tall or short
operators. Table-top designs are also available through H-Square’s Custom Products
Department. Simple design for reliability and low maintenance.
FS-002
|
|
